Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
HeatShield Chimney Cleaning in Highland, UT
We provide independent HeatShield service across Highland: evaluating, cleaning around, and repairing cast-in-place refractory liners in the tall masonry and prefab fireplaces that fill the bench and foothill lots here. The one thing that makes our HeatShield work in Highland different is draft. Because so many homes sit close to the mouth of American Fork Canyon, a liner can be perfectly intact and still smoke into the room when downslope winds hit the stack. We diagnose that alongside the creosote. Call (855) 629-7505 to book. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Highland Residents Choose Us for HeatShield Service
HeatShield is a cast-in-place refractory liner system, a specialist-tier repair that general sweep companies rarely offer. We work with HeatShield because it’s what professionals specify when a masonry flue is cracked, spalled, or simply not safe to burn against any longer. Sweep. Inspect. Repair. All in one visit.
That matters in Highland, where a single home can have two or three flues on a tall stack, and where an insert has often been added to a fireplace that was never sized for it. We bring that history into the diagnostic instead of just running a brush down the flue and handing you a bill.
We’re an independent provider. We’re not affiliated with or authorized by HeatShield, and no manufacturer warranty is implied by our work. What we offer instead is straightforward judgment: we’ll tell you what we found and what it means, and whether a reline is actually the right fix or whether cap and stack correction will solve the smoke problem for a fraction of the cost. Chimney work is all we do, and our technicians have up to 14 years of experience.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common HeatShield Chimney Cleaning Problems We Solve in Highland
- Liner delamination and spalling at the flue collar. On the tall two-story stacks common to Highland’s bench homes, the top of the liner takes the hardest temperature swings. Canyon downdrafts push cold air down a hot flue and the liner face flakes and separates at the collar. We inspect that joint closely because it’s the first place failure shows.
- Cracks and joint separation after heavy burn seasons. Highland fireplaces run hard from November through March, and creosote-fueled chimney fires crack poured refractory liners over time. A hairline crack that looks minor from the firebox can open up under repeated heat cycling, and that’s exactly where hot gases reach framing.
- Oversize flues with an undersized HeatShield liner. A liner that wasn’t correctly sized to the firebox produces weak draft and smoke rollback. In Highland this shows up worst during American Fork Canyon downslope winds, when the flue simply can’t overcome the pressure pushing down on it.
- Water intrusion at the crown and flashing. Foothill-exposed chimneys take wind-driven snow and hard freeze-thaw cycles, and water tracking down the crown degrades the liner’s top edge. Once that edge breaks down, the whole liner is on borrowed time.
- Creosote packed against a sound liner. Not every smoky fireplace needs relining. Heavy glazed creosote from a cold, smoldering burn will choke draft and smell up the house on its own. Creosote removal plus a Level 2 Inspection tells us whether the liner is fine and the problem is fuel and airflow.
HeatShield Service in Highland: What Local Conditions Mean for Your Equipment
Here’s the local reality that shapes this work. Highland’s bench and foothill lots sit close to the mouth of American Fork Canyon, so tall two-story chimney stacks routinely get wind-driven downdrafts that smoke out living rooms even when the flue is clean. A flat valley-floor town like Lehi rarely demands this. A technician working Highland has to evaluate cap style, stack height, and pressure balance alongside creosote, because the two problems look identical from the couch and have completely different fixes. In a typical Highland bench home, a HeatShield-lined masonry fireplace smokes back into the living room during winter canyon downslope winds even after a sweep, because the flue is oversized for the firebox and the cap doesn’t break the downdraft. The right sequence is a Level 2 Inspection, confirmation that the poured liner is intact and correctly sized, then draft correction through a taller or different cap, with a genuine HeatShield refractory rebuild recommended only if the liner is genuinely cracked or delaminated at the specified thickness.
HeatShield Models & Products We Service in Highland
We service the full range of HeatShield liner applications found in Highland homes: cast-in-place refractory chimney liners in both insulated and non-insulated configurations, poured refractory systems for masonry fireplaces, the 1/2-inch and 5/8-inch refractory lining formulations, and liner systems installed as part of wood-burning insert retrofits. That covers the tall two-story masonry stack on a bench lot and the modest prefab fireplace in a foothill home alike.
When a repair calls for material, we use the manufacturer’s genuine refractory mix applied at the specified thickness. Aftermarket pours don’t carry the same cure and density guarantees, and they rarely hold up under Highland’s draft loads and freeze-thaw cycling. The right materials for the repair, not just what’s on the truck.
See the difference
Before
After
Before
After
Before
AfterHeatShield Service Pricing in Highland
Pricing is set per job by a written estimate, and the estimate is free. What drives the number: the number of flues, the height and accessibility of the stack, how much creosote has to come out before we can inspect the liner, and whether the outcome is cleaning, draft correction, or a refractory rebuild.
- Standard chimney sweeping with creosote removal: quoted per flue after we see the setup
- Level 2 Inspection with camera and photo documentation: quoted per chimney
- HeatShield refractory relining: quoted per flue based on diameter, height, and lining formulation
- Chimney cap, crown, and stack-height draft correction: quoted per job
- Chimney Rebuilding where structural masonry is involved: quoted after inspection
Nothing is recommended without camera evidence you can see for yourself, and we’ll say plainly when work can safely wait. Call (855) 629-7505 for an exact quote. Estimates are free.
Serving Highland, UT – Our Local Coverage Area
We serve Highland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – HeatShield Chimney Cleaning in Highland
Because creosote is usually not the cause. On Highland bench lots, the culprit is typically canyon downdraft working against an oversize flue or a cap that doesn’t break the incoming air, and a sweep can’t fix either. Call (855) 629-7505 for an exact quote on a draft evaluation. Estimates are free.
You know by looking at it with a camera, not by guessing from smoke behavior. A Level 2 Inspection shows delamination at the collar, cracks, joint separation, or a degraded top edge. If the liner is sound, we clean and leave it alone. Call (855) 629-7505 to schedule the inspection.
Yes. An oversize flue cools the smoke before it exits, and cool smoke deposits creosote faster. Combined with Highland’s November-to-March burn season and canyon downdrafts, an oversized flue can build glazed creosote in a single winter. Call (855) 629-7505 for an assessment.
Usually something else. Relining corrects a failed or improperly sized liner, but if the liner is intact the honest fix is cap design, stack height, or flue sizing correction. Relining is reserved for genuinely failed flues. Call (855) 629-7505 and we’ll tell you which situation you’re in.
The flue collar for delamination, the liner face for cracks and spalling, the crown and flashing for water intrusion, and the cap for wind damage. Winter here combines deep freeze-thaw with wind-driven snow, and those conditions stress a liner top edge. Call (855) 629-7505 for an exact quote. Estimates are free.
Service Areas Near Highland
We provide HeatShield service in Highland and the surrounding north Utah County and south Salt Lake County communities, including American Fork, Cedar Hills, Draper, Riverton, and Herriman. If you’re on the bench or in the foothills, we know the draft challenges your stack faces.
Book Your HeatShield Service in Highland Today
Get a free estimate on HeatShield service for your Highland home. Call (855) 629-7505. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect, show you what we found, and give you a written estimate before any work begins.
Written by the team at Blackwell Chimney Sweep.